Ram 1500 5.7 HEMI Oil Capacity and Refill Guide
Ram 1500 5.7 HEMI oil capacity is 7 quarts (6.6 L) with filter for common applications. See viscosity checks, refill workflow, dipstick, and oil-life reset.
The Ram 1500 5.7L HEMI oil capacity is commonly 7.0 qt (6.6 L) with filter. Verify the model year, oil specification, viscosity shown by the manual/cap, and final dipstick level.
The Ram 1500 5.7L HEMI oil capacity is commonly 7.0 qt (6.6 L) with filter. Verify the model year, oil specification, viscosity shown by the manual/cap, and final dipstick level. That number is a refill starting point for the identified engine, not permission to pour the entire amount without checking. Oil can remain in galleries, coolers, a tilted pan, or an old filter, and aftermarket pans can change total volume. The safest method is to verify the engine code and model year, use the correct viscosity and approval, refill slightly below capacity, circulate the oil, wait, and finish by the dipstick.
This guide separates similarly named engines and model generations because capacity errors commonly come from a search result that omits the year or engine code. The table also distinguishes “with filter” from “without filter.” During a normal oil change, replace the filter and use the with-filter figure, then confirm the final level on level ground under the conditions specified by the owner manual.
Interactive Ram 1500 5.7L HEMI oil-service workflow
Branded downloads includedPNG and PDF exports carry the TorqueSheet logo, torquesheet.com, source-page URL, and republishing attribution request. The PDF source link is clickable.
Follow the workflow from vehicle identification through final dipstick verification. Published capacities are starting quantities, not a substitute for the level check.
Ram 1500 5.7 Hemi Oil Capacity
| APPLICATION / ITEM | SPECIFICATION | NOTES |
|---|---|---|
| 5.7L HEMI with filter | 7.0 qt (6.6 L) | Ram owner-handbook capacity |
| Normal service | Replace filter | Use with-filter capacity |
| Final setting | Dipstick full mark | Check level on level ground |
| Oil selection | Year-specific | Follow viscosity and Mopar material standard |
Mopar has published the seven-quart with-filter figure across multiple Ram generations, but oil viscosity and material-standard requirements have evolved.
Oil-capacity chart for 1500 5.7L HEMI
Use the chart as an application lookup. The seven-quart capacity is stable across many years, but the required oil specification and viscosity can change. A capacity printed beside the wrong engine code is not “close enough”; even engines sharing the same displacement can have different pans, filters, coolers, or drain-back behavior. If the vehicle has been swapped, rebuilt, or fitted with an aftermarket pan, use the installed hardware manufacturer's capacity and calibration marks.
The most common current application begins near 7.0 qt (6.6 L). Begin below that amount and finish by measurement. The difference between the add and full marks is often about one quart, but do not assume that relationship when the dipstick is aftermarket, damaged, or paired with a non-original tube. Investigate a reading that remains absent or implausibly high.
MDS and eTorque equipment do not remove the need to match the exact oil standard printed for the model year.
Common causes of a capacity mismatch
Mopar has published the seven-quart with-filter figure across multiple Ram generations, but oil viscosity and material-standard requirements have evolved. If the verified dipstick result and the expected quantity disagree materially, stop and identify the cause instead of choosing whichever number is more convenient.
- The lookup used the model name but not the model year or engine code.
- The quoted figure excluded the filter while the filter was replaced.
- The vehicle was not level or the oil had not drained back before checking.
- An oil cooler, remote filter, aftermarket pan, engine swap, or incorrect dipstick changed the system.
- The old filter gasket remained on the housing or a leak began after startup.
- The crankcase was filled to the advertised capacity without a final dipstick check.
Ram 1500 5.7L HEMI specifications can change by model year, engine, platform, wheel, and installed component. Confirm the VIN or engine identity, part numbers, fastener condition, and the current manufacturer instructions before service.
Procedures used with this specification
These steps are the same for every vehicle in this family, so they are documented once rather than repeated on each page. The values above remain specific to this Ram 1500 5.7L HEMI.
Ram 1500 5.7 HEMI Oil Capacity and Refill Guide FAQs
How much oil does the 1500 5.7L HEMI take?+
The Ram 1500 5.7L HEMI oil capacity is commonly 7.0 qt (6.6 L) with filter. Verify the model year, oil specification, viscosity shown by the manual/cap, and final dipstick level. Confirm the year/engine row and finish by the dipstick rather than treating the capacity as an exact pour-in amount.
Technical sources
TorqueSheet favors engine- and component-specific manufacturer instructions over unsourced universal values.
12024 Ram 1500 Owner HandbookPrimary Ram handbook listing 5.7L HEMI oil capacity and service information.↗22011 Ram 1500 User Guide — fluids and capacitiesPrimary Ram handbook listing 5.7L HEMI oil capacity and service information.↗